static ip


Rough notes on setting up an Ubuntu server with docker

Static IP

First, we set up a static IP to our Ubuntu server using netplan. To do so, we created the following file:

/etc/netplan/01-netcfg.yaml

using the following command

sudo nano /etc/netplan/01-netcfg.yaml;

and added the following content to it:

# This file describes the network interfaces available on your system
# For more information, see netplan(5).
network:
  version: 2
  renderer: networkd
  ethernets:
    enp3s0f0:
      dhcp4: no
      addresses: [192.168.45.13/24]
      gateway4: 192.168.45.1
      nameservers:
          addresses: [1.1.1.1,8.8.8.8]

To apply the changes, we executed the following:

sudo netplan apply;

Update everything (the operating system and all packages)

Usually, it is a good idea to update your system before making significant changes to it:

sudo apt update -y; sudo apt upgrade -y; sudo apt autoremove -y;

Install docker

In this setup we did not use the docker version that is available on the Ubuntu repositories, we went for the official ones from docker.com. To install it, we used the following commands:

sudo apt-get install ca-certificates curl gnupg lsb-release;
curl -fsSL https://download.docker.com/linux/ubuntu/gpg | sudo gpg --dearmor -o /usr/share/keyrings/docker-archive-keyring.gpg;
echo   "deb [arch=$(dpkg --print-architecture) signed-by=/usr/share/keyrings/docker-archive-keyring.gpg] https://download.docker.com/linux/ubuntu $(lsb_release -cs) stable" | sudo tee /etc/apt/sources.list.d/docker.list > /dev/null;
sudo apt-get update;
sudo apt-get install docker-ce docker-ce-cli containerd.io;

Install docker-compose

Again, we installed the official docker-compose from github.com instead of the one available in the Ubuntu repositories. At the time that this post was created, version 1.29.2 was the recommended one:

sudo curl -L "https://github.com/docker/compose/releases/download/1.29.2/docker-compose-$(uname -s)-$(uname -m)" -o /usr/local/bin/docker-compose;
sudo chmod +x /usr/local/bin/docker-compose;

Increase network pool for docker daemon

To handle the following problem:

ERROR: could not find an available, non-overlapping IPv4 address pool among the defaults to assign to the network

We created the following file,

/etc/docker/daemon.json

using the command:

sudo nano /etc/docker/daemon.json;

and added the following content to it:

{
  "default-address-pools": [
    {
      "base": "172.80.0.0/16",
      "size": 24
    },
    {
      "base": "172.90.0.0/16",
      "size": 24
    }
  ]
}

We executed the following command to restart the docker daemon and get the network changes applied:

sudo systemctl restart docker;

Gave access to our user to manage docker

We added our user to the docker group so that we could manage the docker daemon without sudo rights.

sudo usermod -aG docker $USER;

Deploying

After we copied everything in place, we executed the following command to create our containers and start them with the appropriate networks and volumes:

export COMPOSE_HTTP_TIMEOUT=120;
docker-compose up -d --remove-orphans;

We had to increase the timeout as we were getting the following error:

ERROR: for container_a  UnixHTTPConnectionPool(host='localhost', port=None): Read timed out. (read timeout=60)
ERROR: An HTTP request took too long to complete. Retry with --verbose to obtain debug information.
If you encounter this issue regularly because of slow network conditions, consider setting COMPOSE_HTTP_TIMEOUT to a higher value (current value: 60).

Stopping all containers using a filter on the name

docker container stop $(docker container ls -q --filter name=_web);

The above command will find all containers whose names contain _web and stop them. That command is actually two commands where one is nested inside the other.

#This command finds all containers that their name contains _web, using the -q parameter, we only get back the container ID and not all information about them.
docker container ls -q --filter name=_web;
#The second command takes as input the output of the nested command and stops all containers that are returned.
docker container stop $(docker container ls -q --filter name=_web);

CentOS 7: Setup a DHCP server and provide specific IP based on MAC address

Step 1: Install DHCP service

We installed the Dynamic host configuration protocol software (DHCP service) using the command:

yum install dhcp;

The dhcp package provides the ISC DHCP service and relay agent.

Step 2: Configure the DHCP service

Afterwards, we created the file /etc/dhcp/dhcpd.conf using the following content:

subnet 192.168.0.0 netmask 255.255.255.0 {
 option routers                  192.168.0.254;
 option subnet-mask              255.255.255.0;
 option domain-name              "bytefreaks.net";
 option domain-name-servers       192.168.0.1;
 option time-offset              -18000;     # Eastern Standard Time
 range 192.168.0.90 192.168.0.99;
}

host coolServer {
 hardware ethernet 0e:e0:4b:b4:28:82;
 fixed-address 192.168.0.80;
}

This configuration allowed us to provide a DHCP service to the network for the subdomain 192.168.0.x with the range [90,99].
Also, we statically defined the IP for our coolServer using a filter based on the MAC address of the machine.
If you do not want to provide any range, only static IPs, then comment out (#) the line that starts with the word range .

Step 3: Start DHCP service

systemctl start dhcpd.service;

Step 4: Check the status of DHCP service

systemctl status dhcpd.service;

It is a good idea to verify that there are no errors, so be sure to check the status of the service.
You can ignore the error that says “you did not define a subnet declaration for all devices” if you do not really need to do it.

Step 5: Permanently enable the DHCP service

systemctl enable dhcpd.service;

Additional:

Disable the DHCP service

systemctl disable dhcpd.service;

Stop the DHCP service

systemctl stop dhcpd.service;