Ετήσια αρχεία: 2017

CentOS 7: Setup a DHCP server and provide specific IP based on MAC address

 στο GNU/Linux  επισημασμένο με ετικέτα CentOS / daemon / DHCP / mac filter / server / static ip Από

Step 1: Install DHCP service

We installed the Dynamic host configuration protocol software (DHCP service) using the command:

yum install dhcp;

The dhcp package provides the ISC DHCP service and relay agent.

Step 2: Configure the DHCP service

Afterwards, we created the file /etc/dhcp/dhcpd.conf using the following content:

subnet 192.168.0.0 netmask 255.255.255.0 {
 option routers                  192.168.0.254;
 option subnet-mask              255.255.255.0;
 option domain-name              "bytefreaks.net";
 option domain-name-servers       192.168.0.1;
 option time-offset              -18000;     # Eastern Standard Time
 range 192.168.0.90 192.168.0.99;
}

host coolServer {
 hardware ethernet 0e:e0:4b:b4:28:82;
 fixed-address 192.168.0.80;
}

This configuration allowed us to provide a DHCP service to the network for the subdomain 192.168.0.x with the range [90,99].
Also, we statically defined the IP for our coolServer using a filter based on the MAC address of the machine.
If you do not want to provide any range, only static IPs, then comment out (#) the line that starts with the word range .

Step 3: Start DHCP service

systemctl start dhcpd.service;

Step 4: Check the status of DHCP service

systemctl status dhcpd.service;

It is a good idea to verify that there are no errors, so be sure to check the status of the service.
You can ignore the error that says “you did not define a subnet declaration for all devices” if you do not really need to do it.

Step 5: Permanently enable the DHCP service

systemctl enable dhcpd.service;

Additional:

Disable the DHCP service

systemctl disable dhcpd.service;

Stop the DHCP service

systemctl stop dhcpd.service;

Bash: After redirected input file is done, allow user to control application via STDIN 1

 στο Bash  επισημασμένο με ετικέτα cli / concatenate / end of file / eof / keyboard / mix / stdin Από

Recently, we needed to start an application using a script, which application had its own CLI.
After starting it, we had to feed it with some input to configure it before handing it over to the end user.

The application we used was named dog. We wrote into a plain text file (named food) the commands that we needed to feed the application and then we started the execution using a plain input redirect like so dog < food;.
Doing so, resulted into properly feeding the dog application the food data  but it would cause the application to terminate immediately after the food was done as it would also feed the EOF (End Of File) directive to dog.
Apparently, the application after receiving the EOF, it would then terminate without allowing the end user to take control.

To mitigate the problem, we used the cat command to concatenate the input file along with the stdin stream, permitting us to first feed all the data in the food file and then allow the user to input data using the standard input stream.
Our final command resulted in the following solution as below

cat <(cat food) - | dog;

Where - is the special sign for standard input stdin.
cat food can be of course replaced with other commands that produce output on the standard output (stdout).

A bad side-effect of this solution, is that we lost some functionality of the terminal including, but not limited to, using the backspace and navigation.

Find all git repositories and perform a pull operation on them.

 στο Bash  επισημασμένο με ετικέτα cron / find all / git Από

The following command will find all git projects in your home folder and perform a pull operation on them.

find ~ -name ".git" -type d -exec bash -c "echo '{}' && cd '{}'/.. && git pull" \;

The above command is based on finding the .git folders that exist in any clone of a git repository. Once a .git folder is found, it will navigate to its parent folder where it will perform the pull request.

Bonus – Automate the procedure using a cron job

The following entry in crontab allows us to periodically perform a pull request on all the cloned repositories that we have in a specific folder. Specifically, it will perform this operation once every five minutes.

*/5    *    *    *    *    cd /home/bytefreaks/Projects; find . -name ".git" -type d -exec bash -c "echo '{}' && cd '{}'/.. && git pull" \; &> /tmp/bf.git.log

Please note that it would be easier to use an ssh key that does not have a password for this automation.
If you do not, the you will need to either pass the password via this configuration line (not recommended) or have a key agent running to provide the password for the key.

Redirecting standard error (stderr)

 στο Bash  επισημασμένο με ετικέτα redirect / stderr / stdout Από

The following command will redirect stderr to a different file than the one stdout is redirected to:

command >log.txt 2>errors.txt;

In case you want to redirect stderr to stdout (&1), and then redirect stdout to a file you can use the following setup:

command >mixed-log.txt 2>&1;

The following command will have the same effect as the previous one, the difference between them is the way they are implemented. This time we will redirect both the stdout and stderr to a file:

command &> mixed-log.txt;